SKU: Satellite Communication Lab 10202
• Microwave 2.4 GHz operation Satellite Trainer
• 500MHz spectrum analyser provided
• Tele-command and telemetry facility
• Different Baud rates PC-PC link.
• Emulation of variable signal fading, variable thermal noise
• Variable propagation delay.
• Total 4 Variable path loss at uplink and downlink channels
• High RF output power and low noise
• LCD display of PLL synthesized frequency in Transmitter,
• Receiver and Satellite Emulator
• Condenser microphone and speaker for audio link
• Camera and Video to VGA converter for video link
• Satellite has built-in antennas, transponder for link
• Helix (LHCP X 2 & RHCP X 2), Log Periodic X 2, Dish X 2 & Patch X 2 for linear & circular polarization study
• Signal monitoring outputs at uplink & downlink
• C/N and S/N measurement facility
• Frequency :Frequency : 2.4, 2.427, 2.454 & 2.481 GHz PLL Synthesized ISM Band
• Display : LCD 16X2 Backlit Spurious output : 30 dB typical
• RF Output Z : 75 Ohms Unbalanced
• RF output level : +3 dBm nominal
• Path Loss : Upto 35dB variable attenuation
• Audio 1 : Int. 1KHz sine wave / Ext Mic Ext. Function Generator waveform
• Audio 2 : Int. 1KHz sine wave / Ext Mic Ext. Function Generator waveform
• Video : Colour/Monochrome Camera/VCD
• Waveform : upto 5MHz Function Generator
• Digital : Max bit rate 500KHz typical
• RS232 : PC serial port compatible intput
• Tele-command : Selectable 4 bit binary input with selectable 4 addresses
• Enable : Telecommand Frame available at digital input
• FM deviation : Variable on audio and video/data
• Frequency :2.4, 2.427, 2.454 & 2.481 GHz PLL Synthesized ISM Band
• Display : LCD 16 X 2 Backlit
• RF Input Z : 75 Ohms Unbalanced
• Sensitivity : -85dBm
• Path Loss : 20dB typical variable attenuation
• Audio 1out : Speaker inbuilt/output
• Audio 2 out : Speaker inbuilt/output
• Video Out : 5MHz bandwidth, 1V p/p
• Digital : Max bit rate 500KHz typical TTL
• Rs232 : PC serial port compatible output
• Down-converter : 400-500MHz output for spectrum analysis
• Telemetry : 4 bit binary LED output with Selectable 4 addresses
• Valid/Error : Tele-command Frame available at Correction digital output
• RSSI Out : Received signal strength output for C/N Measurement
• Frequency :2.4, 2.427, 2.454 & 2.481 GHz PLL
• Synthesized ISM Band
• Display : 16X2 LCD Backlit
• RF Input Z : 75 Ohms Unbalanced
• Sensitivity : -85dBm
• Uplink Path Loss : 20dB typical variable attenuation
• Telemetry : 4 bit binary LED output with Selectable 4 addresses
• Valid/Error : Telemetry Frame available at digital Correction output
• Frequency :2.4, 2.427, 2.454 & 2.481 GHz PLL Synthesized ISM Band
• Display : 16X2 LCD Backlit
• Spurious output : - 30 dB typical
• RF Output Z : 75 Ohms Unbalanced
• RF output level : +3 dBm nominal
• Path Loss : Upto 25dB variable attenuation
• Tele-command : Selectable 4 bit binary input with selectable 4 addresses
• Enable : Telecommand Frame available at digital input
• Test Output : Audio 1, Audio2, Video, Digital
• Down-converter : To spectrum analyzer 400-500 MHz
• RSSI Out : Received signal strength output for C/N measurement
• Band limiting : 18MHz fixed typical
• Noise addition : Variable
• Signal delay : upto 0.6s on Audio1 channel
• Signal fading : Variable 10dB
• Frequency : 10 MHz – 500 MHz
• Center frequency : 4 digit LED display
• Accuracy : + 0.1%
• Resolution : 100KHz
• Sensitivity : -90dBm
• Attenuator : 20dB External
• Input Impedance : 50 Ohms (BNC)
• Horizontal scan : upto 50MHz/div continuous
• Center freq. : Variable control
• Dynamic range : 60dB typical
• CRO Output : Linear X out (BNC)
• : Log Y out (BNC)
• Antennas : Microstrip Log periodic X 2, Helix LHCP X 2 & Helix RHCP X 2, Microstrip Patch X 2, Parabolic Dish X 2
• Mount : Antenna mount X 2
• Software : PC Serial communication software
• Accessories : Camera, Microphone, Video to VGA converter Card, Cables BNCBNC X6, Tee connector X2, RS 232 Rx & Tx Cables
Dimensions: 58X52X44cms Weight: 22Kgs
• To set up an active & passive satellite communication link and study their difference. To study the advantages of satellite communication. To study the communication satellite link design: process of transmitting a signal to a satellite (UPLINKING), reception of same signal via satellite (DOWN LINKING) and functioning of transponder.
• To measure baseband analog signal parameters.
• To measure the signal parameters like fm deviation in an analog FM/FDMTV Satellite link on spectrum analyser.
• To study the functionality of a satellite MODEM.
• To measure Linear and Circular polarization of antennas on spectrum analyser.
• To measure the C/N ratio, threshold on spectrum analyser.
• To measure the S/N ratio.
• To study the effect of fading and measure the fading margin of a received signal on spectrum analyser.
• To measure the Propagation Delay of signal.
• To measure pathloss using spectrum analyser.
• To study noise on spectrum analyser.
• To measure the digital baseband signal parameters in a satcom link. To measure the range of baud rates that the system can support.
• To send telecommand and receive the telemetry Data and study the operation of a codec.
• To setup a RS-232 satellite communication link using com ports of PC.
• To calculate Bit Error Rate in a satcom link.
Free shipping to any address in South Africa
011 805 5030 / 086 138 6548 - Phone orders
Monday-Friday, 08:00-17:00
Category: Antenna / Satellite / Radar / RF Trainers / Microwave Test Benches
Product code (SKU): Satellite Communication Lab 10202